News:

New Round added to ASRA schedule: VIR North Course

Main Menu

Things to do with a MW SS bike

Started by DEVINC, September 29, 2009, 02:38:27 PM

0 Members and 1 Guest are viewing this topic.

DEVINC

Just wondering if anyone has any suggestions on little things to do to my 06 r6 to make it perform better. I am definitely more focused on my riding, I was just wondering if anyone had any cool suggestions to keep me busy while we have time off from riding. (rotor lightening, ram air mods, etc.) .

Been bored waiting to race  :sleeping2:

2old2fat2slow

Shave weight and do some track days on the tracks you race at.
Thanks to:Lithium Motorsports, Vondari Racing, Continental Tires of North America, Absolute Cycle, RaceConti,Next Level Motorsports, Mize Mobile, Vortex, Woodcraft

DEVINC

shave weight on bike? haha. im actually pretty scrawny so i guess the bike would lose weight first, where from tho...?

George_Linhart

If you are never going to put the bike back on the street some small amount of weight savings can be pretty easy.  Customize a race wire harness - elimiate all the connectors for stuff you don't need like a horn, turn signals and head-lights.  Look around the bike and remove all those extra brackets for the parts you took off.  Cut down the sub--frame or replace it (lw aluminum or carbon fiber).  Replace the stock battery with something much smaller and lighter.  I think you can get lightweight clutch baskets and plates to replace the heavier stock ones.

You can send your rear brake rotor cut or drilled - a number of people do this for a small fee.

Next steps get really expensive really fast, but, you can repalce a lot of stock nuts and bolts with aluminum and titanium ones.  Replace the stock axles with magnesium.  Get an aftermarket racing fairing stay.  Install a kit alternator - it should save about a pound of rotating weight so the bike will be lighter and rev faster.

Some guys get absolutely anal about going over every single inch of the bike and removing excess material in any place that it is not a stressed member.   

You can always go superbike and then lightweight wheels are legal and you can open the engine and lighten/polish the crank, get carillo (or titanium) rods.  While you have the cases split you could have the transmission gears drilled and lightened by a specialty shop.

I am sure I am forgetting some of the tricks but this should be enough to get you started.

George

DEVINC

George,
Thanks. These are good ideas to get me started!   :thumb:

Sobottka

49
Lithium Motorsports
Suspension Solutions
http://www.facebook.com/team.chouffe

F2RGK

Quote from: DEVINC on September 29, 2009, 06:02:42 PM
George,
Thanks. These are good ideas to get me started!   :thumb:


Devin, don't listen too George....he's a banker!!!  LMAO!!  Of course he's going to tell you to lose weight...he sits behind a desk all day and figures who is credit worthy!!!  Shaaah.  Oh, he rides a Ducati too!  LOL!!!! 
If you're not Smilin' while you're ridin', then QUIT!

Super Dave

Replace the front brake lines.  Geometry is a key on bikes.  I won't go through my old set up on shock lengths and fork heights, but it makes a difference.  Save weight?  520 chain and sprockets are a start.  Find out what guys are using on R6's at your local track for gearing.  And bodywork is weight savings too.  If you're down south and you're gonna run WERA, make sure you can modify the wiring harness for the classes you might run.

Keep it simple.  Make it race/crash worthy, focus on getting it slowed down (brakes) and handling (geometry, correct spring rates [if you're a lightweight, the stock rear spring is way stiff], maybe replacing shock and fork work), and then ride the thing.  Find someone that can help you in your riding to cut your learning curve.  You need someone to tell you "no" on some things your trying so that you don't waste your time and money.
Super Dave

DEVINC

good call Dave. lines and chain already have. Eric from GMD set me up nicely with springs in my forks. I still need to set up my rear shock and general geometry of the chassis has not been touched yet.  :thumb:

Super Dave

Quote from: DEVINC on September 30, 2009, 08:56:00 AM
good call Dave. lines and chain already have. Eric from GMD set me up nicely with springs in my forks. I still need to set up my rear shock and general geometry of the chassis has not been touched yet.  :thumb:
How much do you weigh?  I think the stock rear spring is good for someone that weighs around 210#.  If you're under that, it keeps that back end way up and it never seems to feel like it bites well on the gas hard. 
Super Dave

DEVINC

w/o gear... last time i checked about 140. So I would imagine it is too stiff. I try to work on my braking and when doing it "hard and late" it seems like the back end stands up too much to me. Maybe i'm just stabbing too hard rather than easing into it? btw, you really think that bone vitamin is good to take even if already taking a general multivitamin?

Super Dave

Quote from: DEVINC on September 30, 2009, 09:12:22 AM
w/o gear... last time i checked about 140. So I would imagine it is too stiff. I try to work on my braking and when doing it "hard and late" it seems like the back end stands up too much to me.
Well, the spring can never sag like it should when you're on it.  So, it's always going to be in the top part of the shock's stroke.  That reduces your trail at that point, it moves the CG up and forward.  Yes, the back end should stand up as a result.  Gotta get it into the ball park.  Springs are good.


Quote from: DEVINC on September 30, 2009, 09:12:22 AMbtw, you really think that bone vitamin is good to take even if already taking a general multivitamin?
Good question.  I know I've taken some here and there just because I had some floating around.  We've given some of them to my wife's grandmother (93 now) to help her bones.  It has a lot of joint lubricating properties, so, sure, it would be a good addition to a multivitamin in my opinion.  I'm not a scientist, but that product was recommended to me by one. 
Super Dave