I like to build stuff, I was looking into making some gauges and found the LM2907 "Frequency to Voltage converter". Pretty simple stuff, it takes a pulse signal from either switched current (like your coil input) or from a magnetic "hall effect" sensor (like on your speedo drive) and converts it into a variable voltage. Pretty easy to make your own tach, shift light, speedo, etc... I already got 6 to play with ;)
Here's the manual...
http://www.national.com/ds.cgi/LM/LM2907.pdf
How are you making it? Putting it on bread board? Also, you might want to make sure you isolate the front end from electrical noise. Or, if your putting it on a PCB, choke out the ground plane. Bikes seem to radiate quite a bit of noise. One of th processor boards I was trying for the telemetry project we've been working on kept locking up due to EMI. You should throw this into our telemetry thread. Maybe we can incorporate it into our current layout. Wouldn't be a big deal. Let me know if you need any help. :)
Right now I have it on a cheap RS PCB.
I don't have the plans handy but it's got a 8 volt regulator, cap, resistor and zener diode filtering it.
I have the "controller" built to read a hall effect sensor, I found the plans for a helicopter rotor tach ;D I still need to test it out on my SV and if it works I'm gonna drive a series of LED's off it @ 5mph increments.
Don't be suprised if I take you up on your offer for help ;)
Sounds like that might do it for filtering. If it won't, you'll know first time you start the bike. If it starts acting funny, see if you can get your hands on an o-scope. You'll see it if your picking up noise. With my bike I could see the actual injection PPS AC waveform jump across the screen. Anyway, let me know if you need anything. :)
and you'll be hooked on this kind of stuff soon too. ;D Pretty soon your bike will have electronics for everything ;D
I considered trying to use a BS2 BASIC stamp to make a custom fuel injection system for my SV650 but I've been busy with other things, like my Christmas tree stand ;D
http://www.racemotorcycles.com/cgi-bin/board/YaBB.pl?board=ccs1;action=display;num=1103641529
I wish I had time to mess with custom one off stuff :( I always get stuck with work stuff.
No job is worth not having free time... in my opinion. You can't buy more time.
Don, I got an email from Austria today about this thread :D
Yo Don, the stuff on that link seems really complex.
I was hoping it'd be some really simple directions for building my own shift light. Can you share with me the electronics for dummies version?
H.
BTW Dan, if you do want/need assistance drilling bolts and nuts for your bike, give me a call or e-mail. You can swing by and I'll lead you through the drilling.
Just bring a fistfull if 1/16th" drill bits.
Thanks H. I'm holding out on the drilling until I get all the aftermarket stuff put on the bike. I can hep you build the shit light if you want it. 8)
Brilliant! I'll take you up on your offer. Why do you call it a "nuts light"?
Just send me a list of what parts I need to pick up and where best to find 'em.
Keep in mind that this'll be for a '94 F2. The electronics on that bike are minimal so there may not be the easy tap in that you might envision.
H.
QuoteBrilliant! I'll take you up on your offer. Why do you call it a "nuts light"?
Just send me a list of what parts I need to pick up and where best to find 'em.
Keep in mind that this'll be for a '94 F2. The electronics on that bike are minimal so there may not be the easy tap in that you might envision.
H.
LOL. I forgot the "F" in shift light, so the auto editor made SH!T turn into Nuts. ;D Let me find the distributors and such and we'll go from there. I'll post links and also email everything to you. 8)
Future Electronics is the distrubtor for our state. They're located in Farmington Hills, but they don't sell "Direct" to consumers. I'll order a handfull of them. I'll get them from the rep. as samples. 8)
BRILLIANT! 8)
I ordered the samples H. Should have them within a week or so. 8)
Okay.
Just send me an e-mail when you have the stuff and let me know what you need for me to get (e.g., bracket to hold a particular sized item) to make this happen.
BTW, from what you know of this sample light, will it be flush mount, lipstick/pen style or surface mount thing? I don't have much of a dash in my cockpit. I'll need to think about "where" to mount it in addition to "how"
Still waiting. sigh ::)