Print Page - Magnaflux and Undercut Trans Work?

Title: Magnaflux and Undercut Trans Work?
Post by: grasshopper on February 20, 2007, 09:32:41 AM

Any recommendations on getting a trans magnafluxed and undercut in the Chicagoland area? Any recommendations at all?

Thanks,

Title: Re: Magnaflux and Undercut Trans Work?
Post by: Jeff on February 20, 2007, 09:56:00 AM

www.mdracingstp.com

Have Drucker do it... he's not really in Chicago, but it's worth the few hours drive to me personally...

Title: Re: Magnaflux and Undercut Trans Work?
Post by: grasshopper on February 20, 2007, 10:01:45 AM

Does Drucker do it himself? I doubt it. He more than likely sends it out. Please correct me if I'm wrong.

I'm just curious if there is a place in the Chicagoland area. If not It will go through Brian at Valley Racing.

Thanks Jeff

Nick

Title: Re: Magnaflux and Undercut Trans Work?
Post by: Super Dave on February 20, 2007, 10:34:08 AM

I think pretty much everyone uses R&D in Florida for transmission stuff. I don't have a link, but that's where guys I know from California send stuff, guys from Minnesota, Illinois, and me, when I have my new H1 trans.

Title: Re: Magnaflux and Undercut Trans Work?
Post by: grasshopper on February 20, 2007, 12:23:10 PM

Quote from: Super Dave on February 20, 2007, 10:34:08 AM
I think pretty much everyone uses R&D in Florida for transmission stuff. I don't have a link, but that's where guys I know from California send stuff, guys from Minnesota, Illinois, and me, when I have my new H1 trans.

Thanks Dave, thats where Valley racing pointed me to.

Attention to Dave:
R&D Motorsports
1632 North Hercules Ave. Building G
Clearwater Fl. 33765
Phone: 727-447-4552

Title: Re: Magnaflux and Undercut Trans Work?
Post by: tzracer on February 20, 2007, 01:07:55 PM

Mark Junge sent my transmission to Fast by Gast.

http://www.fastbygast.com/

Title: Re: Magnaflux and Undercut Trans Work?
Post by: BrianC636 on February 20, 2007, 01:38:34 PM

http://www.aperaceparts.com/transmissions.html

Title: Re: Magnaflux and Undercut Trans Work?
Post by: EX_#76 on February 20, 2007, 02:28:36 PM

Quote from: Super Dave on February 20, 2007, 10:34:08 AM
I think pretty much everyone uses R&D in Florida for transmission stuff. I don't have a link, but that's where guys I know from California send stuff, guys from Minnesota, Illinois, and me, when I have my new H1 trans.

+1

That is where Ed and I get undercutting done.

Title: Re: Magnaflux and Undercut Trans Work?
Post by: grasshopper on February 20, 2007, 04:15:54 PM

Thanks fellows, I'm going to stay with R&D. I trust Brian at Valley and I know the one tranny that was already done by R&D is awesome.

I was basically curious if anyone was doing this service in the Chicagoland area.

Title: Re: Magnaflux and Undercut Trans Work?
Post by: cbr600_mj on February 20, 2007, 04:30:44 PM

Hey there,

I had my tranny undercut by Matt Drucker last month.

I went with him due to his reliability and he did some work on my bike last year.

A friend of mine had referred him.

Mike

Title: Re: Magnaflux and Undercut Trans Work?
Post by: onedwn5up on February 23, 2007, 04:47:02 PM

+2. that is where my trans went to and they did a beautiful job. Wasn't cheap but what is in this sport anyway? They also check all the bearings and will replace any of the bearings that show signs of drag as well.

Quote from: grasshopper on February 20, 2007, 12:23:10 PM
Thanks Dave, thats where Valley racing pointed me to.

Attention to Dave:
R&D Motorsports
1632 North Hercules Ave. Building G
Clearwater Fl. 33765
Phone: 727-447-4552

Motorcycle Racing Forum

Motorcycle Talk => Wrenching => Topic started by: grasshopper on February 20, 2007, 09:32:41 AM